Where do I connect the fan?

Any technical questions about the Epiphany chip and Parallella HW Platform.

Moderator: aolofsson

Where do I connect the fan?

Postby baseballguy » Tue Jul 08, 2014 1:38 pm

Hi everyone, I recently just bought a small fan for the Parallella board, but I don't know where to connect it or if soldering is required? Where do I connect the black,red, and yellow wires? I think they are called a 3-pin Power Connector.

Sorry for my limited knowledge. I'd appreciate any help
baseballguy
 
Posts: 40
Joined: Tue Jul 08, 2014 1:36 pm

Re: Where do I connect the fan?

Postby baseballguy » Tue Jul 08, 2014 2:01 pm

This is the fan I bought.

http://www.microcenter.com/product/3928 ... D_Case_Fan

Are the specs fine?
baseballguy
 
Posts: 40
Joined: Tue Jul 08, 2014 1:36 pm

Re: Where do I connect the fan?

Postby 9600 » Tue Jul 08, 2014 2:36 pm

baseballguy wrote:Are the specs fine?


Since it's a 12V fan, to run it at full speed you would need to connect it to a 12V power supply (the Parallella board runs on 5V).

However, it may be that the fan will run at 5V and generate sufficient airflow to keep the board cool.

Where to take a 5V supply for a fan has been discussed in another thread.

Regards,

Andrew
Andrew Back (a.k.a. 9600 / carrierdetect)
User avatar
9600
 
Posts: 997
Joined: Mon Dec 17, 2012 3:25 am

Re: Where do I connect the fan?

Postby greytery » Tue Jul 08, 2014 7:59 pm

The specs for the fan suggest that it's noisy @ 26.8 dBa, presumably when full-on @ 12v. This noise will be much less if you connect (solder) it to the board's 5v supply. But I'm sure you can get quieter examples if you continue to search.

Cheers,
tery
User avatar
greytery
 
Posts: 205
Joined: Sat Dec 07, 2013 12:19 pm
Location: ^Wycombe, UK

Re: Where do I connect the fan?

Postby AlbertoGP » Thu Jul 10, 2014 4:49 pm

Normally, the black wire is "Ground", the red wire is "+12V", and the yellow wire is the tachometer signal: two or four pulses per turn of the fan, to tell the mainboard how fast it is spinning.

To cool the Parallella, you need to plug only the ground and +12V wires: the fan will run a the speed proportional to the voltage, with the standard RPM if you supply the standard 12V for which this fan is rated.
If you give it less volts, it'll spin slower. That's how a computer's motherboard or fan controller can make it adapt to the temperature inside the computer.

I've looked at the specifications for that fan (http://www.nzxt.com/product/detail/94-fz-120mm-non-led-case-fan) and it does not indicate the starting voltage: that's the minimum voltage at which the fan will start spinning, which will be lower than the standard 12V. Some 12V fans have a starting voltage of 4.5 and can work with the 5V you can get from the Parallella board, others require for instance 8V and will need their own power supply.
In your case you'll probably have to try it out with a 5V power source.

I've put what I found out trying different fans here: cooling and more memory?
Before getting those small fans I used a 92mm 12V case fan I had at hand: I tried to power it with 5V and it worked very well, but other two 12V fans I tried at the time did not start up with 5V.
AlbertoGP
 
Posts: 41
Joined: Sat May 10, 2014 10:17 am
Location: Saarbrücken, Germany


Return to Epiphany and Parallella Q & A

Who is online

Users browsing this forum: No registered users and 6 guests